Cisco Systems IGX 8 Spezifikationsblatt PDF herunterladen

APPENDIX

-1

System Specifications

This appendix contains system speciﬁcations.

General

This section provides general system information on the IGX 8.

System Capacity: 1 shelf with 8 card slots.

Requires 2 dedicated front slot(s) for NPMs.

Requires 2 dedicated back slots for SCMs (1 slot with blank plate).

Up to 6 T1/E1 circuit ports.

Up to 6 T1/E1 packet trunks.

Up to 48 synchronous data ports.

Up to 25 Voice, Data, and/or Frame Relay Module groups.

Enclosure Size: IGX 8 Standalone/Rackmount:

Height: 25 ins. (63.5 cm) standalone; 24.5 ins. (62.3 cm), rack

Width: 19.9 ins. (50.5 cm), standalone; 19 ins. (48.3 cm.), rack

Depth: 26.5 ins. (67.3 cm), standalone and rack-mount

Shipping Weight: 270 pounds (122.7 kilograms)

Clearance Requirement: Min. clearance: 30 inches front; nominal 30 ins. rear; 12 ins. side.

Power Input Voltage: AC system: 100 to 240 VAC (90–264 under-voltage and

over-voltage tolerance), 47 to 63 Hz.

DC system: –42 to –56 VDC.

Each AC supply can provide up to 400 watts to the card shelves.

Space for 4 power supplies.

Current Requirements: Conﬁguration dependent - use Network Design Tool for exact

requirements. For planning purposes, use the following:

• AC System 10 Amps Max. for 110 VAC, 5 A for 220 VAC.

• DC System 20 Amps max. at –48 VDC; 25 Amps at –42 VDC (worst case)

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - System Specifications

APPENDIX-1System SpecificationsAThis appendix contains system speciﬁcations.GeneralThis section provides general system information on the IGX 8.Syste

Seite 2 - Voice Circuit Support

-10 IGX 8 Installation Manual, Release 8.2.0ATM InterfaceNetwork SynchronizationType of Service: Permanent Virtual Circuit (PVC)Interface Types: User-

Seite 3 - Data Channel Support

-11Network Management ControlNetwork Control Terminal: StrataView Plus workstation and StrataCom software required forgraphical display of network sta

Seite 4

-12 IGX 8 Installation Manual, Release 8.2.0

Seite 5 - T1 Interface

-2 IGX 8 Installation Manual, Release 8.2.0Voice Circuit SupportInput AC PowerConnector:IEC 16 Amp input connector. 6 different power cords are availa

Seite 6 - E1 Interface

-3Data Channel SupportSync. Data Interfaces: RS-232C/D, RS-449/422, V.24, X.21, and V.35with IGX 8 as DCE or DTE.High-Speed Data Rates(HDM):2.4 Kbps t

Seite 7 - T3 Interface

-4 IGX 8 Installation Manual, Release 8.2.0Digital Data Service InterfacePorts per card: Four.Electrical Interface: Digital Data System (DDS)—AT&T

Seite 8 - E3 Interface

-5T1 InterfaceLine Rate: 1.544 Mbps, ± 50 bps (± 200 bps VCO lock range).Line Code: Bipolar AMI or B8ZS.Framing Formats: Fractional T1, adjacent or al

Seite 9 - Frame Relay Interface

-6 IGX 8 Installation Manual, Release 8.2.0E1 InterfaceLine Rate: 2.048 Mbps, ± 50 bps (± 200 bps VCO lock range)Line Code: Bipolar AMI or HDB3Line Im

Seite 10 - Network Synchronization

-7T3 InterfaceLine Rate: 44.736 Mbps ± 20 ppm, asynchronous.Line Code: B3ZS.Clock Source Mode: Internal (Asynchronous).Signal Level: DSX-3.Framing For

Seite 11 - Network Management Control

-8 IGX 8 Installation Manual, Release 8.2.0E3 InterfaceLine Rate: 34.368 Mbps ± 20 ppm, asynchronous.Line Code: HDB3.Clock Source Mode: Internal (Asyn

Seite 12

-9Frame Relay InterfaceType of Service: Permanent Virtual Circuit (PVC).Data Interface: Per ITU-T I.122 and ANSI T1/S1 Standards.Data Transfer Protoco

Kommentare zu diesen Handbüchern

Keine Kommentare

Cisco Systems IGX 8 Spezifikationsblatt

Stöbern Sie online oder laden Sie Spezifikationsblatt nach Modems Cisco Systems IGX 8 herunter. Cisco Systems IGX 8 Specification Sheet Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Modems Cisco Systems IGX 8