Cisco Systems G18 G-.SP Bedienungsanleitung

BURNERSBRULEURSBRENNERQUEMADORESBRUCIATORIComplying withEMC 89/336/CEELV 73/23/CEETechnical Documentation CIB Unigas S.p.a. - Campodarsego (PD)M03978C

10VBSVBS+-Fig. 12Fig. 11Fig. 10Fig. 12aAIR FLOW ADJUSTMENTBurner G18SPLoose the screw VBS and rotate the air damper in the desiredposition, to set the

11PART II: OPERATION MANUALLIMITATIONS OF USETHE BURNER IS AN APPLIANCE DESIGNED AND CONSTRUCTED TO OPERATE ONLY AFTER BEING CORRECTLYCONNECTED TO A H

12CARVRTRCVFig. 13Fig. 13aABCD60°644645°1054660°844645°1254660°844645°12546G1 8 SPPG28SPPG30TNPART III: MAINTENANCEAt least once a year carry out the

13Fig. 14CHECK OF THE IONIZATION CURRENTTo check the detector signal follow theprcedure shown in fig. 14.If the signal is not within the prescribedran

14ELECTRICAL DIAGRAM code 01-369 BURNER G18SPELECTRICAL DIAGRAM code 04-575 BURNER PG25SP1 - Electric supply 230V 50Hz 2N a.c.2 - Don't reverse P

15ELECTRICAL DIAGRAM code 04-574 BURNER PG30TNEVG1 Light oil solenoid valve Ist stageEVG2 Light oil solenoid valve IInd stageF FusesFR PhotoresistorIL

16SPARE PARTS BURNER G18SPMAINTENANCEPOS. DESCRIPTION CODE POS. DESCRIPTION CODE1HOUSING 3010019 19 BLAST TUBE 30900552CONDENSER 6030004 20 COMBUSTION

17SPARE PARTS BURNERS PG25SP - PG30TNMAINTENANCEPOS. DESCRIPTION PG25SP PG30TN1 ELECTRIC BOARD 6100086 61000862 THERMAL RELAY --- ---3 SOCKET FOR FLAM

18APPENDIX: COMPONENTS CHARACTERISTICSFLAME CONTROL DEVICE LANDIS LOA24 Page 18LIGHT OIL PUMPS Page 19LANDIS AUTOMATIC CONTROLLER LOA24FOR LIGHT OIL B

19Technical characteristicsVoltage 220V-15%..240V+10% or 100V-15%...110V+10%Frequency 50...60Hz +/- 6%External fuse max.10A slow actionContact flow:-

2PREFACETHIS MANUAL IS SUPPLIED AS AN INTEGRAL AND ESSENTIAL PART OF THE PRODUCT AND MUST BE DELIVEREDTO THE USER.INFORMATION INCLUDED IN THIS SECTION

20SUNTEC AS oil pumps- Oil- Flow up to 75 1/h (c.600,000 kcal/h - 700 kW)- Twin-pipe system- Single-pipe systemTechnical dataMounting On flange or hub

21OperationThe gear-set draws oil from the tank through the built-in filter and transfers it to the valve that regulates the oil pressure or tne nozzl

22Twin pipe installation Single pipe installation (remove theby-pass plug “P”)A Closed by-pass solenoid valveB Opened by-pass solenoid valveC Opened c

23

Via C. Colombo, 9 - 35011 Campodarsego (PD) ItalyTel. +39-049-9200944 - Fax +39-049-9200945-9201269Internet: www.cibunigas.it - E mail: cibunigas@cibu

3FOREWORD3) GENERAL INSTRUCTIONS DEPENDING ON FUEL USED3A) ELECTRICAL CONNECTION* For safety reasons the unit must be efficiently earthed andinstalle

4ABBLCCLDEGKH P MG1 8 SP275 90 200 365 475 340 255 115 230 125 121÷134 M8Fig. 1PART I: INSTALLATION MANUALTECHNICAL DATABURNER MODEL IDENTIFICATIONBur

5Fig. 1aFig. 2Fig. 3Fig. 3a00.20.40.60.811.21.41.61.86 8 10 12 14 16 18 20-10123410 12 14 16 18 20 22 24 26 28 30-1-0.500.511.522.5310 12 14 16 18 20

6MOUNTINGS AND CONNECTIONSThe burners are despatched in cardboard packages.The packaging contains the following items:1 burner;2 flexible light oil tu

7G18SP PG25SP PG30TNFig. 6Fig. 5 Fig. 5bFig. 5a

8BARGPH 8 9 1011121314151617181.75 6.02 6.38 6.73 7.05 7.37 7.67 7.96 8.24 8.51 8.77 9.022.00 6.88 7.29 7.69 8.06 8.42 8.77 9.10 9.42 9.72 10.02 10.31

9Fig. 7Fig. 9Fig. 8LIGHT OIL PUMPSSUNTEC AS57CSuction height: 0.5 barAdvised value to preventair separation from oil: 0.35 barRated speed: max. 2850 r