Cisco Systems WSC2960XR48FPSI Bedienungsanleitung Seite 147
- Seite / 178
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
How to Configure Tunneling
Configuring an IEEE 802.1Q Tunneling Port
SUMMARY STEPS
1.
configure terminal
2.
interface interface-id
3.
switchport access vlan vlan-id
4.
switchport mode dot1q-tunnel
5.
exit
6.
vlan dot1q tag native
7.
end
8.
Use one of the following:
•
show dot1q-tunnel
•
show running-config interface
9.
show vlan dot1q tag native
10.
copy running-config startup-config
DETAILED STEPS
PurposeCommand or Action
Enters the global configuration mode.configure terminal
Example:
Switch# configure terminal
Step 1
Enters interface configuration mode for the interface to be
configured as a tunnel port. This should be the edge port in the
interface interface-id
Example:
Switch(config)# interface
Step 2
service-provider network that connects to the customer switch.
Valid interfaces include physical interfaces and port-channel logical
interfaces (port channels 1 to 48).
gigabitethernet2/0/1
Specifies the default VLAN, which is used if the interface stops
trunking. This VLAN ID is specific to the particular customer.
switchport access vlan vlan-id
Example:
Switch(config-if)# switchport access vlan
Step 3
2
Sets the interface as an IEEE 802.1Q tunnel port.switchport mode dot1q-tunnel
Step 4
Catalyst 2960-XR Switch VLAN Configuration Guide, Cisco IOS Release 15.0(2)EX1
OL-29440-01 133
Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling
How to Configure Tunneling
- 15.0(2)EX1 1
- CONTENTS 3
- OL-29440-01 v 5
- OL-29440-01 vii 7
- OL-29440-01 ix 9
- Contents 10
- Document Conventions 11
- Timesaver 12
- Related Documentation 13
- Command Modes 15
- Table 1: Command Mode Summary 16
- Using the Help System 17
- CLI Error Messages 18
- Configuration Logging 19
- Recalling Commands 20
- 12 OL-29440-01 26
- Configuring VTP 27
- Information About VTP 28
- VTP Modes 29
- VTP Advertisements 30
- VTP Version 2 31
- VTP Version 3 31
- VTP Pruning 32
- OL-29440-01 19 33
- VTP and Switch Stacks 34
- VTP Configuration Guidelines 34
- Passwords for the VTP Domain 35
- VTP Version 36
- Default VTP Configuration 37
- How to Configure VTP 38
- Enabling the VTP Version 42
- Enabling VTP Pruning 43
- Monitoring VTP 48
- OL-29440-01 37 51
- 38 OL-29440-01 52
- Configuring VLANs 53
- Restrictions for VLANs 54
- Information About VLANs 54
- Supported VLANs 55
- VLAN Port Membership Modes 55
- Normal-Range VLAN Overview 56
- Token Ring VLANs 57
- 44 OL-29440-01 58
- OL-29440-01 45 59
- Default VLAN Configuration 60
- How to Configure VLANs 61
- Deleting a VLAN 63
- Monitoring VLANs 70
- Configuration Examples 71
- OL-29440-01 59 73
- 60 OL-29440-01 74
- Configuring VLAN Trunks 75
- Restrictions for VLAN Trunks 76
- Information About VLAN Trunks 76
- Layer 2 Interface Modes 77
- Allowed VLANs on a Trunk 78
- Load Sharing on Trunk Ports 78
- OL-29440-01 65 79
- Feature Interactions 80
- How to Configure VLAN Trunks 81
- 82 OL-29440-01 96
- 84 OL-29440-01 98
- OL-29440-01 85 99
- 86 OL-29440-01 100
- Configuring Private VLANs 100
- Private VLAN Domains 101
- Secondary VLANs 102
- Private VLANs Ports 102
- Private VLANs in Networks 103
- 90 OL-29440-01 104
- OL-29440-01 91 105
- Private VLANs and SVIs 106
- SUMMARY STEPS 107
- DETAILED STEPS 108
- Example: 113
- Monitoring Private VLANs 115
- Where to Go Next 118
- Additional References 118
- OL-29440-01 105 119
- 106 OL-29440-01 120
- Configuring VMPS 121
- Restrictions for VMPS 122
- Information About VMPS 122
- OL-29440-01 109 123
- How to Configure VMPS 124
- Before You Begin 126
- Reconfirming VLAN Memberships 127
- Changing the Retry Count 129
- Monitoring the VMPS 131
- 120 OL-29440-01 134
- Tunneling 135
- Layer 2 Protocol Tunneling 136
- OL-29440-01 123 137
- Information about Tunneling 138
- OL-29440-01 125 139
- IEEE 802.1Q Tunneling 139
- 126 OL-29440-01 140
- Native VLANs 141
- System MTU 142
- OL-29440-01 129 143
- 130 OL-29440-01 144
- OL-29440-01 131 145
- 132 OL-29440-01 146
- How to Configure Tunneling 147
- Monitoring Tunneling Status 160
- 148 OL-29440-01 162
- Configuring Voice VLANs 163
- Restrictions for Voice VLANs 164
- Information About Voice VLAN 164
- Cisco IP Phone Voice Traffic 165
- Cisco IP Phone Data Traffic 165
- 152 OL-29440-01 166
- How to Configure Voice VLAN 167
- Monitoring Voice VLAN 171
- 160 OL-29440-01 174
- OL-29440-01 IN-1 175
- IN-2 OL-29440-01 176
- OL-29440-01 IN-3 177
- IN-4 OL-29440-01 178
Verwandte Produkte und Handbücher für Netzwerk-Switches Cisco Systems WSC2960XR48FPSI
(122 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern