Cisco Systems OL-10426-01 Betriebsanweisung Seite 77
- Seite / 150
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4-31
Cisco WAN Modeling Tools Guide
OL-10426-01, Rev. A0
Chapter 4 Configuration Tables and Fields
Model Options
Model Options
Selecting Model options from the Config<Global menu allows you to specify the model parameter
settings listed in Table 4-17.
Table 4-18 Execute Menu Model Parameter Settings
Setting Defaults Description
Optimize LDI Ports YY
—NMT tries to optimize the cost of the LDP cards by using lower cost
LDP-4 cards instead of LDP-8 cards.
If no, NMT only uses LDP-8 cards. You can still explicitly call for an
LDP card with a specific line count.
Group Bursty Conns YY
—NMT groups connections when their number exceeds the maximum
number of LCONS. An LCON is a resource required for each network
route with similar properties. The grouping of connections allows more
routed connections in a network.
If no, NMT does not group connections and fails to build a site when a
grouping is required.
Distribute Groups YY
—NMT optimizes the grouping of connections to smooth network
loading.
If no, NMT does not optimize grouping.
Use SRM-3T3 on
MGX 8220
NY
—NMT will provision an SRM-3T3 service redundant module on all
MGX 8220 shelves.
If no, NMT will provision an SRM-3T3 service redundant module only if
the case connection interface requires it.
Bundle Voice with CCS YY—NMT will bundle voice connections with CCS signalling and create
a transparent connection (type T) to carry line signalling.
If No, NMT will not bundle voice connections; it is your responsibility to
specify the channel for CCS signalling.
Use Preferred Route YY
—route the connection with the preferred route if one exists.
If no, use the current route.
Note This does not apply to failure analysis.
Note CET Extractions will set this field to ‘N’.
Use Port ID YY— NMT assigns slots and ports based on hub and feeder IDs.
If no, NMT treats all ID fields as though they were zero filled, and
provisions links and connections using its own algorithms.
Port ID Over Redundancy NY
—the system eliminates the redundant card if another card has
requested the hub ID of the backup card.
If no, the system gives backup cards precedence over another card that
was assigned the same port. In this case, NMT overrides the hub ID and
moves one of the connections to a different location.
New Share with Port ID NY
—NMT allows connections IDs of zero to share ports with connections
having IDs other than zero.
If no, NMT does not allow this.
- Customer Order Number: 1
- Text Part Number: OL-10426-01 1
- CONTENTS 3
- 3 Using the NMT 3-1 4
- 5 NMT Execute Commands 5-1 5
- 6 NMT Reports 6-1 5
- 8 NMT Map 8-1 6
- 11 SpreadSheet Interface 11-1 7
- Contents 8
- Obtaining Documentation 10
- Documentation Feedback 11
- Submitting a Service Request 13
- Functionality of the NMT 18
- Gaps 21
- Data Translation Tools 22
- System Requirements 23
- Installing the NMT 24
- Creating a Working Directory 25
- Installing the NMT 26
- Upgrading the NMT Software 28
- Starting the NMT 28
- Removing NMT 29
- Removing Sub-applications 31
- Using the NMT 33
- NMT Menu Bar 34
- File Menu 35
- Configure Menu 36
- Chapter 3 Using the NMT 37
- File Menu 37
- Utilities 38
- Edit Options 38
- Display Menu 39
- Report Menu 40
- Keyboard Commands 41
- Table 3-1 Sun Key Assignments 42
- Key Function Description 42
- Modeling Processes 43
- Error Checking 44
- Troubleshooting NMT 45
- Troubleshooting NMT 46
- General Table Information 47
- Sites Table 48
- Sites Table 49
- Y- for feeder; 50
- N- for router 50
- Links Table 52
- Minimal Link Table Usage 53
- Links Table 54
- Link Special Cases 56
- Voice Table 57
- Voice Table 58
- Data Table 60
- Data Table 61
- Bursty Table 63
- Table 4-8 Bursty Table 64
- Bursty Table 65
- Bursty Table Special Cases 69
- Interface Table 70
- Interface Table 71
- Feeder Table 72
- Card Table 73
- Groups and Network Table 74
- Nodes Table 75
- Network Settings 75
- Network Settings 76
- Model Options 77
- Modeling Implicit Feeders 78
- Feeders 79
- Modeling Explicit Feeders 80
- Obsolete Products 81
- Obsolete Products 82
- FastPAD 84
- Port Concentrator 87
- Tiered Networks 88
- NMT Execute Commands 89
- Preferred and Directed Routes 90
- PNNI Routing 91
- Fail Analysis Command 92
- Build Sites Command 92
- Optimize Command 93
- NMT Command Results 94
- Optimize Command 95
- NMT Reports 97
- Link Load Report 98
- Connection Routes Report 99
- Failed Connections Report 99
- Parts List Report 100
- Using the Map Tool 101
- OL-10426-01, Rev. A0 102
- Chapter 6 NMT Reports 102
- Using the Map Tool 102
- Creating a Graphical Display 103
- NMT Utilities Command Line 105
- NMT Map 107
- Chapter 8 NMT Map 108
- NMT Map Startup 108
- Zooming the Map 112
- Panning the Map 113
- Map Color Coding 113
- NMT Map Main Menu 114
- NMT Map Main Menu 115
- Adding New Groups 116
- Deleting Groups 118
- Saving Your Work 119
- Retrieving Map Data Into NMT 120
- Configuration Extraction Tool 121
- Using the CET 122
- Step 4 This step is optional 123
- Other CET Commands 124
- Troubleshooting CET 125
- Troubleshooting CET 126
- Remote CET Extracts 128
- Remote CET Extracts 129
- Troubleshooting 130
- Probable 131
- Solution 131
- WANDL — Third-Party Interface 133
- WANDL_directory 136
- SpreadSheet Interface 137
- NMT to Microsoft Excel 139
- Microsoft Excel to NMT 140
- Usage Review 141
- SSI TroubleShooting 142
- CND PC Import Utilities 143
- CND PC Import Utilities 144
- CND PC Utilities 146
Verwandte Produkte und Handbücher für Software Cisco Systems OL-10426-01
Software Cisco Systems 10200 Bedienungsanleitung
(214 Seiten)
(214 Seiten)
Software Cisco Systems 5.x Bedienungsanleitung
(248 Seiten)
(248 Seiten)
Software Cisco Systems 15327 Bedienungsanleitung
(584 Seiten)
(584 Seiten)
Software Cisco Systems ESW 500 Bedienungsanleitung
(442 Seiten)
(442 Seiten)
Software Cisco Systems 6500/7600 Bedienungsanleitung
(134 Seiten)
(134 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern