Cisco Systems 3000 Bedienerhandbuch Seite 189
- Seite / 234
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
11-11
Cisco TelePresence System 3000
OL-14521-01
Chapter 11 Field-Replaceable Unit Guide
Replacing a Codec Unit—Part Number CTS-CODEC-PRI-G2 (Primary Codec) or CTS-CODEC-SEC (Secondary Codec)
See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” for additional information.
Step 5 Remove the codec from the Display structure.
Step 6 Remove the L brackets from the codec.
See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” for additional information.
Step 7 Remove the cable management bar from the codec. Retain the bar and the screws.
See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” for additional information.
Step 8 Attach the L-brackets and Cable management bar to the replacement codec.
See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” for additional information.
Step 9 Attach the codec to the display structure front feet using the screws that you removed in Step 4.
Step 10 Turn the codec power switch to the On position.
Caution Make sure each PDU power switch is still in the Off position.
Step 11 Reattach the cables according to your temporary masking tape identification.
See Chapter 8, “Routing Power and Signal Cables”, for additional information.
Step 12 Attach the cables to the cable management bar using tie wraps.
Step 13 If the replacement unit was the Primary codec, follow these steps.
a. Open a browser on a computer connected to the network.
b. Access the Cisco Unified Communications Manager interface.
c. Change the MAC address for the Primary codec to its new address.
Step 14 Power on the system by turning the power switches to the On position on the two left PDUs, single right
PDU, and (if present) auxiliary control unit or PDU on the rear center of the display assembly.
Step 15 In the browser on the computer, type in the IP address of the primary codec unit.
Step 16 Enter the required information at the login screen. The Cisco TelePresence Administrator window
appears.
Step 17 Verify the status of the Cisco Unified Communications Manager (seen in the lower left portion of the
window) is Enabled/Up.
Step 18 Select Hardware Setup to verify the cameras, displays, speakers, and microphones are working
properly.
Step 19 Perform the Auto Adjust camera setup procedure. This sets the white balance to the correct levels. See
the “Setting Up the Cameras” section on page 9-7 for detailed instructions.
Note If you are replacing the primary codec, power it on and complete all steps before powering on the
secondary codecs. This prevents the secondary codecs from being affected by any software and
peripheral upgrades to the primary codec.
- Assembly Guide 1
- Use & Care Guide 1
- Field-Replaceable Unit Guide 1
- CONTENTS 3
- Contents 4
- Introduction 9
- Conventions 9
- Guidelines 10
- Related Documentation 10
- Overview 11
- Chapter 1 Overview 12
- Chapter Organization 12
- Assembly Overview 13
- Conventions and Terminology 14
- Tools and Equipment List 15
- Tools and Equipment List 16
- Building the Display Assembly 17
- Figure 2-1 Leveling feet 18
- Figure 2-2 Codec Safety trays 19
- 18 - 22” (45.7 cm - 55.8 cm) 26
- Leveling Alignment Points 30
- Leveling Goals 31
- Apply the Black Buffer strips 36
- Figure 4-8 Light Cup bracket 47
- Figure 4-15 Four L-brackets 54
- Accessory Cabinet 65
- CTS3K-FUR-MAPLE 67
- Figure 5-3 Left Display shelf 68
- Figure 5-6 Accessory Cabinet 71
- Figure 5-8 Left Display shelf 73
- Figure 5-11 Accessory Cabinet 76
- Building the Table Assembly 77
- Miscellaneous Table Items 78
- Figure 4 Right Table segment 84
- Figure 5 Right-most Table Leg 85
- Figure 6 Center Table segment 86
- Figure 8 Left Table segment 88
- Figure 10 Left-most Table leg 90
- Attach the table door 91
- Figure 13 Accessory cabinets 93
- 22 23 24 97
- Figure 19 Right Table segment 99
- OL-14521-01 100
- Figure 23 Left Table segment 103
- Figure 25 left Most Table Leg 105
- Figure 26 Microphone Assembly 106
- Figure 28 Accessory cabinets 108
- Elements 109
- Projector Assembly 110
- Privacy Panel Assembly 110
- Codec Assembly 110
- Parts List 111
- Camera Target Assembly 112
- Switch Bracket 112
- Figure 7-1 Camera Assembly 113
- Figure 7-5 Projector Assembly 117
- Figure 7-6 Projector Assembly 118
- Figure 7-7 VGA Module 119
- Figure 7-12 Codec Assembly 124
- Figure 7-13 Codec Assembly 125
- Figure 7-14 Codec Assembly 126
- Figure 7-17 Speaker Assembly 129
- Figure 7-18 Speaker Assembly 130
- Figure 7-19 Speaker Assembly 131
- Parts List 135
- Table Leg Power 140
- Projector Power 140
- Table Leg Signal 141
- IP Phone Signal 141
- Microphone Signal 141
- Projector Signal 141
- VGA Peripheral 141
- Projector HD Video to Codec 142
- Microphones 144
- RJ45 Power over Ethernet 149
- HDMI connector 149
- First-Time Setup 155
- Figure 9-1 Bootup Completed 156
- Figure 9-2 System IP Address 157
- Setting Up CTS Components 158
- Setting Up the Displays 159
- Troubleshooting Displays 160
- Cisco TelePresence 3000/3200 160
- Setting Up the Cameras 161
- Up/down screw 162
- Left/right screws 162
- Rotation screws 162
- Setting Up CTS Components 163
- Show All Camera Targets 164
- Flipping the Video Image 164
- Focus the Camera 164
- Troubleshooting Cameras 166
- Setting Up the Speakers 167
- Setting Up the Microphones 167
- Troubleshooting Microphones 168
- Setting Up the Projector 169
- Other Devices 176
- Maintaining the Projector 178
- Powering Off the System 180
- Removing the Camera Cluster 180
- Uncrating and unpacking: 181
- Removing Audio Components 182
- Removing a Display Shelf 183
- Replacement Bulbs 192
- Replacing a Light Fixture 192
- CTS-AV-EXP 193
- CTS-PRJTR-BL-GEN1 195
- CTS-LIGHT-CTRL 199
- Replacing a Display Shelf 199
- Replacing a Display Shelf 200
- Replacing a Table Top Section 201
- Section Assemblies 205
- Assemblies 217
- 69-1835-01, CTS3K-M 229
- Equipment 231
- Australia 232
- Central Europe 232
- India, UAE, South Africa 232
- North America 233
- Switzerland 234
- United Kingdom 234
Verwandte Produkte und Handbücher für Nein Cisco Systems 3000
Nein Cisco Systems 3750 Bedienungsanleitung
(176 Seiten)
(176 Seiten)
Nein Cisco Systems OL-4266-08 Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Nein Cisco Systems MDS 9100 Bedienungsanleitung
(70 Seiten)
(70 Seiten)
Nein Cisco Systems Soho series Bedienerhandbuch
(58 Seiten)
(58 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.196 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern