Cisco Systems 3000 Bedienerhandbuch Seite 164
- Seite / 234
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
9-10
Cisco TelePresence System 3000
OL-14521-01
Chapter 9 First-Time Setup
Setting Up CTS Components
Figure 9-6 Correct Camera Target Alignment—Left Display
• Click Hide Camera Target to remove the alignment images.
• Click Done when you complete the adjustment.
Show All Camera Targets
• Click Show All Camera Targets to align each camera independent of the other cameras.
Flipping the Video Image
• Click Flip Video on Each Display to display a mirror image—meaning to simulate the image that
attendees will see—for the selected screen(s). Use this feature to make sure all three cameras are
vertically aligned.
Focus the Camera
• Place the small target on the table.
• Click Setup, then click Show Focus Target.
• Adjust the small target so that the green box encloses some of the patterns on the small target.
• Adjust the focus ring on the camera lens so the lines on the target are in focus. The ring is labeled
“N – 8”. The thumbscrew (or 0.9 mm Allen wrench) is used to unlock the focus ring.
• Click Hide Focus Targets, then click Done when you complete the adjustment.
Attaching the Camera Hood Assembly
• After you complete the camera adjustment, attach the camera hood assembly. See Figure 9-7.
Note Attach the top hood before attaching the bottom hood.
Caution Do not overtighten the screws, or use a power screwdriver to tighten the screws. In addition, make sure
that you use screws of the correct length (20 mm). Overtightening the screws, or using a screw that is
too long, can cause the plastic hoods to break.
Red plus
sign within
black cross
Red lines
Table
edge
Red
Vertical line
205766
- Assembly Guide 1
- Use & Care Guide 1
- Field-Replaceable Unit Guide 1
- CONTENTS 3
- Contents 4
- Introduction 9
- Conventions 9
- Guidelines 10
- Related Documentation 10
- Overview 11
- Chapter 1 Overview 12
- Chapter Organization 12
- Assembly Overview 13
- Conventions and Terminology 14
- Tools and Equipment List 15
- Tools and Equipment List 16
- Building the Display Assembly 17
- Figure 2-1 Leveling feet 18
- Figure 2-2 Codec Safety trays 19
- 18 - 22” (45.7 cm - 55.8 cm) 26
- Leveling Alignment Points 30
- Leveling Goals 31
- Apply the Black Buffer strips 36
- Figure 4-8 Light Cup bracket 47
- Figure 4-15 Four L-brackets 54
- Accessory Cabinet 65
- CTS3K-FUR-MAPLE 67
- Figure 5-3 Left Display shelf 68
- Figure 5-6 Accessory Cabinet 71
- Figure 5-8 Left Display shelf 73
- Figure 5-11 Accessory Cabinet 76
- Building the Table Assembly 77
- Miscellaneous Table Items 78
- Figure 4 Right Table segment 84
- Figure 5 Right-most Table Leg 85
- Figure 6 Center Table segment 86
- Figure 8 Left Table segment 88
- Figure 10 Left-most Table leg 90
- Attach the table door 91
- Figure 13 Accessory cabinets 93
- 22 23 24 97
- Figure 19 Right Table segment 99
- OL-14521-01 100
- Figure 23 Left Table segment 103
- Figure 25 left Most Table Leg 105
- Figure 26 Microphone Assembly 106
- Figure 28 Accessory cabinets 108
- Elements 109
- Projector Assembly 110
- Privacy Panel Assembly 110
- Codec Assembly 110
- Parts List 111
- Camera Target Assembly 112
- Switch Bracket 112
- Figure 7-1 Camera Assembly 113
- Figure 7-5 Projector Assembly 117
- Figure 7-6 Projector Assembly 118
- Figure 7-7 VGA Module 119
- Figure 7-12 Codec Assembly 124
- Figure 7-13 Codec Assembly 125
- Figure 7-14 Codec Assembly 126
- Figure 7-17 Speaker Assembly 129
- Figure 7-18 Speaker Assembly 130
- Figure 7-19 Speaker Assembly 131
- Parts List 135
- Table Leg Power 140
- Projector Power 140
- Table Leg Signal 141
- IP Phone Signal 141
- Microphone Signal 141
- Projector Signal 141
- VGA Peripheral 141
- Projector HD Video to Codec 142
- Microphones 144
- RJ45 Power over Ethernet 149
- HDMI connector 149
- First-Time Setup 155
- Figure 9-1 Bootup Completed 156
- Figure 9-2 System IP Address 157
- Setting Up CTS Components 158
- Setting Up the Displays 159
- Troubleshooting Displays 160
- Cisco TelePresence 3000/3200 160
- Setting Up the Cameras 161
- Up/down screw 162
- Left/right screws 162
- Rotation screws 162
- Setting Up CTS Components 163
- Show All Camera Targets 164
- Flipping the Video Image 164
- Focus the Camera 164
- Troubleshooting Cameras 166
- Setting Up the Speakers 167
- Setting Up the Microphones 167
- Troubleshooting Microphones 168
- Setting Up the Projector 169
- Other Devices 176
- Maintaining the Projector 178
- Powering Off the System 180
- Removing the Camera Cluster 180
- Uncrating and unpacking: 181
- Removing Audio Components 182
- Removing a Display Shelf 183
- Replacement Bulbs 192
- Replacing a Light Fixture 192
- CTS-AV-EXP 193
- CTS-PRJTR-BL-GEN1 195
- CTS-LIGHT-CTRL 199
- Replacing a Display Shelf 199
- Replacing a Display Shelf 200
- Replacing a Table Top Section 201
- Section Assemblies 205
- Assemblies 217
- 69-1835-01, CTS3K-M 229
- Equipment 231
- Australia 232
- Central Europe 232
- India, UAE, South Africa 232
- North America 233
- Switzerland 234
- United Kingdom 234
Verwandte Produkte und Handbücher für Nein Cisco Systems 3000
Nein Cisco Systems 3750 Bedienungsanleitung
(176 Seiten)
(176 Seiten)
Nein Cisco Systems OL-4266-08 Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Nein Cisco Systems MDS 9100 Bedienungsanleitung
(70 Seiten)
(70 Seiten)
Nein Cisco Systems Soho series Bedienerhandbuch
(58 Seiten)
(58 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.148 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern